Ford New Holland 630, 640, 650, 660 Round Baler Service Manual 40063040 English

Brands: Ford New Holland / New Holland Agriculture

Equipment Type: Round Baler

Manuals Type: Service Manual

Machine Model & Serial Number: 630, 640, 650, 660

Region: N/R

Book Code: 40063040

Issued: N/R

Language: English

Pages: 422

File Format: Portable Document Format (PDF)

Remark: Comprehensive manual covering PTO, Gearbox, Slip Clutches, Hydraulics, and the complete Bale Command Electrical/Mechanical Systems.

Table of contents

• SECTION 1 - GENERAL INFORMATION
  • Precautionary Statements
  • Safety Decals
  • Basic Components
  • Driveline Schematic
  • Hardware and Minimum Tightening Torques
  • Conversion Charts
• SECTION 2 - PTO DRIVELINE
  • PTO Removal
  • Front PTO Shaft Disassembly
  • Rear PTO Shaft Disassembly
  • Inspection and Assembly
  • Slide Collar Quick-Disconnect
  • Shaft and Clutch Removal
• SECTION 3 - GEARBOX REMOVAL
  • Gearbox Removal (Models 630, 640, 650, 660)
  • Gearbox Rebuild (540 RPM & 1000 RPM)
  • Gearbox Installation
• SECTION 4 - STANDARD AND WIDE PICKUPS
  • Standard Pickup (Finger Replacement, Cam Bearing, Slip Clutch, Removal)
  • Wide Pickup (Finger Replacement, Cam Bearing, Auger Repair, Feeder Repair)
  • Cam Track Replacement
• SECTION 5 - SLIP CLUTCHES
  • Main Drive Slip Clutch
  • Floor Roll Drive Clutch
  • Sledge Roll Drive Clutch
  • Special Tools
• SECTION 6 - FLOOR ROLL AND STARTER ROLL GROUP
  • Floor Roll Removal and Inspection
  • Starter Roll - Model 630 (Removal and Installation)
  • Starter Roll - Models 640, 650, 660 (Removal and Installation)
• SECTION 7 - APRON ROLL GROUP
  • Releasing Belt Tension
  • Drive Roll Removal
  • Apron Drive Roll Declutch
  • Idler Rolls
• SECTION 8 - APRON BELTS
  • Belt Failure Analysis
  • Repairing Belt Lacing
  • Belt Tracking
  • Installation of Endless Belts
• SECTION 9 - SLEDGE ROLL GROUP
  • Follower Roll
  • Stripper Roll
  • Middle Roll
  • Sledge or Pivot Arm
  • Pivot Roll
• SECTION 10 - HYDRAULIC SYSTEM
  • Tailgate Lift System
  • Cylinder Removal and Repair
  • Lockout Valve
  • Belt Tension System (Single & Double Cylinder)
  • Relief Valves
  • Pickup Lift Cylinder
  • Troubleshooting
• SECTION 11 - TWINE WRAPPER SYSTEM - MODEL 630
  • Adjustments
  • Drive Motor Replacement
  • Twine Arm/Drive Removal and Assembly
  • Electrical Control Box & Full Bale Alarm Switch
  • Electrical Diagram
• SECTION 12 - AUTO-WRAP TWINE SYSTEM - MODELS 640, 650, AND 660
  • Twine Wrapping Cycle
  • Twine Wrapper Adjustments
  • Twine Tubes, Knives, and Supports
  • Clutch and Brake
  • Cam, Cam Follower, and Worm Gears
  • Trip Slide and Linkage
  • Full Bale Alarm
• SECTION 13 - BALE COMMAND MECHANICAL SYSTEM - MODELS 640, 650, AND 660
  • Twine Wrapping Cycle and Adjustments
  • Twine Wrapper Repair (Tubes, Knives, Slides)
  • Net Wrapping Cycle
  • Knife Safety Latch and Net Wrapper Adjustments
  • Net Wrapper Repair (Duckbill, Cam Plate, Brake)
• SECTION 14 - BALE COMMAND ELECTRICAL SYSTEM - MODELS 640, 650, AND 660
  • Components and Operation
  • Adjustments (Tailgate Sensor, Bale Size Sensor, Actuator Sensor)
  • Replacing Electric Components
  • Wire Harness Connector Repair
  • Troubleshooting (Error Messages, Self-Diagnostic Tests)

Introduction
This service manual provides the technical information needed to properly service Ford New Holland Roll-Belt round balers. Use this manual in conjunction with the operator's manual for complete operation, adjustment, and maintenance information. On Ford New Holland equipment, left and right are determined by standing behind the unit, looking in the direction of travel.